Page 16 – Airheads Beemer Club

Camshafts, broken cam tips, cam sprockets, lifters (followers), alternator & cam seals, crank nose bearing, etc. Sports-cams installations. Assembly lubricants.

STOCK, original equipment camshafts:

For the stock cams, at .0787″ valve lift (2 mm), the timings are as follows, keep in mind that two types of these cams installation available, the 3° advanced one & the not advanced one.

R50/5, R60/5, and R60/6 to 1975:
BMW issued a SI on that camshaft, saying that some published information was NOT correct. BMW said the correct figures are:
Intake Opens TDC; Intake Closes 40° ABDC; Exhaust Opens 40° BBDC; Ex Closes was illegible, but I am sure it said 40° BTDC. If you were to look up the sprocket and camshaft in the present parts fiche, it would be 11-31-1-250-253, sprocket.
284° camshaft, used UP TO 09/1975, 11-31-1-259-262.

UNfortunately, BMW is confusing itself. You will find that other manuals say Intake Opens 40°ATDC….all the numbers are 40°; that includes the intake opening at 40° ATDC.

You must be a member to view complete articles on this website. If you are already a member, you can log in here. If you aren’t a member yet, you can purchase a membership here.

Engine, frame, and other numbers/characters. How to read and interpret them. How does BMW identify the year of your motorcycle, etc. Serial numbers. VIN (Vehicle Identification ‘Numbers’) & other identifications. How to identify your motorcycle and major assemblies.

This article contains a large amount of information regarding vehicle numbers and identifications, most especially for BMW Airhead motorcycles, but much of this information also applies to other motorcycles, and even your automobile, truck, etc. Information may seem confusing at first. You are advised to slowly read this entire article, and then re-read; and then look at the numbers on your own bike(s), car, truck, etc.

You may be interested in the information in: https://bmwmotorcycletech.info/models.htm and https://bmwmotorcycletech.info/transmission.htm. Those two articles have some further identification information.

There is a LOT of wordy reading here …but, it can be important!

NON-USA-SHIPPED-BIKES:
BMW may use different frame and motorcycle identification systems for non-U.S.A. motorcycles. There may be a letter or two letters, followed by a serial number. There may be a serial number followed by one extra number, and then the type of motorcycle. Seven (7) digits are used for the serial number. I do not know what the letters nor the 8th digit means, it could be a check-digit. The VIN system of 17 characters may be absent, in favor of just the Serial Number, with possibly a very small BMW roundel stamping and a letter or two or other number or two. This has especially been seen in later Airheads for ECE shipments. In general, the 17 character VIN system was introduced in approximately 1980-1981.

You must be a member to view complete articles on this website. If you are already a member, you can log in here. If you aren’t a member yet, you can purchase a membership here.

Serial/frame identification numbers, year, code, power output, from the earliest BMW motorcycles to mid-1990’s

NOTES:

(1) This article’s information was gathered from quite a number of sources, places and publications; but especially from several old factory (German literature) publications. It is believed mostly, but not absolutely correct. BMW factory literature varies in production numbers and serial numbers for quite a few models. BMW has, at times, confused…and mixed-up…their own figures. This has been particularly so when BMW has used both reserved serial numbers range for a model; and, serial numbers for actual production. BMW vehicle numbers are the serialized number of the frame or engine or both, the more modern versions of which can be 6 or 7 digits, and can be seen on the engine, and/or frame. After ~1980, the numbers are usually the last 7 digits in the new 17 character VIN numbering system, but this is not universal for all Country’s shipped-to. From 1984, BMW stopped stamping serial numbers into the area next to the engine oil dipstick. There is a LOT more to all this. See (5) below; and, see my companion article: https://bmwmotorcycletech.info/IDnumbrs.htm.

You must be a member to view complete articles on this website. If you are already a member, you can log in here. If you aren’t a member yet, you can purchase a membership here.

1 2 3 … 13 14 15 16

Posts navigation