Category: Technical Tips

Open post

Rekeying a Seatlock

Recently I had occasion to replace the seatlock in my R100, which was old, and rotated in its housing, making it hard to actually lock the seat. I checked in with my local dealer, and they said I could get a generic lock, with a matching key, for $23, or I could get a matched lock (set up to work with my existing key) for $50 and 3 months wait.

I decided I’d rather spend $23 and practice my locksmithing skills. This is an article describing how to do the same thing, while hopefully avoiding a few of 
the mistakes I made in the process.

Take a look at this page in general (lock picking) and particularly page 5 from that series for some good visualizations of how a pin-and-tumbler lock works. This is the type of lock used in the seat of the R100 (and probably many other similar vintage Airheads).

Overview

This procedure is broken down into 4 basic parts: getting the lock out of the bike, getting the pins out of the old lock, putting them in the new lock, and putting the lock back in the bike. While the specifics of installation, removal and pin-access may not apply to other locks on the bike (or in general), the rekeying steps can easily be applied to other locks.

Without any instruction, it took me about 30 minutes to do the actual rekeying, having spent 15 minutes beforehand, removing the lock. Reinstalling the lock took about 10 minutes, but would have taken less if I’d kept the seat on (I wanted to take pictures). I think it’d take most people 30-45 minutes to do the whole thing if you read through and understand these instructions.

The Procedure

I’ll describe this in a step-by-step method, referring to pictures as appropriate. Click on pictures to enlarge them. Comments about what I did are in italics.

Step One: Remove the lock from the bike

The seat latch mechanism is attached to the bike by 
way of two long screws that thread into the same plate that holds the side handle and the latch button. The heads aim back towards the tire/center of the bike. It’s easiest to take off these screws with a very short #2 phillips head screwdriver, but a longer one will do. Just unscrew them, and the latch box and cover will come off in your hand.

The lock is secured to the bike with a metal ring, that’s then attached to the body lock with a single screw. The screw is a #1 Phillips screw, and is best taken out 
with a fairly short screwdriver again. Once the ring is removed, the lock body should fall out pretty easily. I accidentally messed up the small screw on my lock by using too large a screwdriver. It eventually came out, but was pretty well unusable.

You must be a member to view complete articles on this website. If you are already a member, you can log in here. If you aren’t a member yet, you can purchase a membership here.

Continue readingMore Tag

New Keys for Your /5

I recently finished going through the process of reviving a 1973 R75/5. One of the challenges I faced was that of missing keys. Sure, the ignition nail key was there, but the keys for the seat lock and the steering head lock were missing. I needed to remove the lock for the fork in order to complete frame painting, and really wanted matching keys for both the seat and fork locks if at all possible. This precluded me from simply drilling it out. I was pretty sure that the locks were original to the frame, and that the keys should be the same for each.

So, here is what worked for me…

First, go to your local dealer and buy a few correct key blanks.
Remove the seat lock mechanism, and detach the lock housing. Don’t lose the small screw that holds the lock to the striker mechanism.
Take the blanks to a competent locksmith and ask them if they can make an impression cut key. Keep looking for someone who will give it a try. Now, just so you know, I was advised that they might damage the lock mechanism while making a key in this manner. If they (or you) are uncomfortable making an impression-cut key, the lock may be disassembled and the tumblers opened up for their key making efforts, but it is critical that they get the pins back together in the same order to have the fork lock work with this key.
OK, we’ll assume that you have a key that works with the seat lock cylinder. You will try it in the fork lock and, surprise, it won’t work!! Here’s what to do:
Look at the key that you have. You should see four valleys in the key blank, which were cut by the locksmith. You will also notice that they are evenly spaced along the key, and also that there is room on the end closest to the handle of the key for another cut to be made. Starting at the end of the key furthest from the handle, we’ll refer to these as cuts #1, #2, #3 and #4. The trick is that the seat lock uses four tumblers, and the fork lock uses five. You will need to cut the last one, #5, yourself.

You must be a member to view complete articles on this website. If you are already a member, you can log in here. If you aren’t a member yet, you can purchase a membership here.

Continue readingMore Tag

Bike Storage Preparation

It’s that time of year again, so I thought I would post the storage procedures that are contained in the 1978 BMW Owner’s Manual for those of you that don’t have access to such. The following is a reproduction of the storage procedures specified by BMW on page 35 of the 1978 BMW Owner’s Manual:

If you intend to lay up your motorcycle during the cold season of the year or for a long period, the following precautions will help to guard against corrosion and superficial damage:
Drain the oil when the engine is warmed up, clean the oil mesh strainer and oil sump.
Add corrosion inhibiting oil up to the lower mark on dipstick (app. 1 Liter = 1.05 US quarts). Run the engine for about 1 minute off-load. Remove the oil filter and close the empty filter chamber. When storing for more than 6 months, drain oil from gear-box, swing arm and final drive and add corrosion inhibiting oil. Contents: gearbox 0.4 liter (0.4 US quart), swing arm 0.05 liter (0.05 US quart). Place the machine on its center stand, engage 2nd gear and turn the engine at a fast idle for a few seconds.

You must be a member to view complete articles on this website. If you are already a member, you can log in here. If you aren’t a member yet, you can purchase a membership here.

Continue readingMore Tag

Cleaning Exhaust Systems

Cleaning Exhaust systems:
Pipes, headers, mufflers, etc., can all be cleaned with 0000 grade of steel wool. Use of 000 grade should be reserved for the worst cases. Exhaust pipes polishes to reduce bluing are available, most do little, and the bluing tends to come back soon. A particular problem is that exhaust systems tend to get oily grunge & other fun stuff such as burned boot heel material on them that gets thoroughly baked onto the surface. Late model Airheads have pre-muffler/collectorson which can can be ‘wire brushed’ with a steel or brass wire wheel/brush, but they are more abrasive to the surface. Brass bristled brushes are safer. Wire brushes may be your last resort if items are truly a big mess, this is particularly so if your items are chrome plated steel & are “rusting”.  Strong chemical means, which will not eat the metal like steel brushes will, work well for heavily baked-on oil/grease/etc. I HIGHLY recommend the entire process be done OUTDOORS.

Clean off any oil/grease you can, with a petroleum solvent. Kerosene; paint thinner; Stoddard solvent; MEK; Acetone; whatever you have. Wash with very hot water & strong dish washing detergent mixture. If the items are still mounted in your bike, you want to mask off, by whatever good means, the bike from the next step. You do NOT want any aluminum castings getting strong ‘oven cleaner’ on your castings, etc.

Obtain a spray can of OVEN CLEANER. Get ONLY the type containing sodium hydroxide (common household lye). Rarely, these days, you might find potassium hydroxide, it is also OK. NO OTHER TYPE of chemicals but these two provides seriously strong chemical cleaning against burned-on grease/oil. Sodium bicarbonate is NOT going to work hardly at all.

If you can, warm the parts to be cleaned. The hotter the parts, the faster the stuff works…but, NEVER higher than water boiling temperature. YOU ABSOLUTELY MUST WEAR SAFETY GOGGLES!!  If any spray gets on you, WASH IT OFF, right now, NO waiting. KEEP IT OUT OF YOUR EYES. Try hard NOT to breathe the spray. Spray the surface generously. DO NOT BREATHE-IN, WHILE SPRAYING. How fast the chemical works depends on temperature and that it remains wet. It is OK to use a foggy spray of water to keep the chemical wet, if it is showing signs of drying. In particularly egregious cases you want a thick layer plus you want it covered so it will stay wet, perhaps overnight. The chemical must be wet. It is better to do this job with the parts off the bike, but that may be inconvenient. After a while, perhaps 15 minutes or longer, wash off very thoroughly with water. Use a stiff floor scrubbing type of brush or modify a stiff paint brush by shortening the bristles so it is even stiffer.   If the wet surface feels soapy/slippery, it is not washed off enough.

You must be a member to view complete articles on this website. If you are already a member, you can log in here. If you aren’t a member yet, you can purchase a membership here.

Continue readingMore Tag

19 inch FRONT Snowflake Wheel Recall

UPDATE:  The silver replacement wheels are no longer available (36-31-1-238-959).  Gold wheels are available and the recall will be honored.   36-31-1-238-960.

19 inch FRONT CAST ALUMINUM SNOWFLAKE wheels were recalled.  NOT 18 inch front wheels.  NOT 18 inch rear wheels.  Recall is ONLY for certain AIRHEADS 19 inch front cast aluminum snowflake wheels.

I still hear occasionally about an old recalled wheel that is still in service. There was a BMW factory recall on SOME FRONT 19″ cast snowflake wheels, & only those! Supposedly a U.S. Federal Recall Campaign never goes out of date. The RECALL is world-wide, & there are specific recall campaigns in the various countries. BMW will provide the recall service, as described in this article, for the BIKE, the bike identification is needed……..AFAIK! I have yet to hear of/from anyone who brought in a wheel to be exchanged & the wheel was not tied to a specific bike identification. You could be the first to tell me the details!

You must be a member to view complete articles on this website. If you are already a member, you can log in here. If you aren’t a member yet, you can purchase a membership here.

Continue readingMore Tag

Improved ATE Braking

From the Airheads mailing list

I see a question and comments about improving front braking on a 1978 R80 from a single disk to dual. One person said go to brembo brakes.

It can be done, but prepare for a snowflake front wheel, the spoked one won’t fit with Brembos. Also you will need the later model down tubes as the attachment of the dampeners is by different means. So you just can’t replace the lowers. (But you can use the originals, if one can get some parts machined).

The wheel cylinders were of different sizes, there are some 38 MM units and some 40 mm units, the 40s give more brake power, the R75s and 80 had 38s. The R100 units and later (75 – 76) and R90S had 40s. So look at the cylinders, it is stamped on there some where. You can’t go by colors, some are silver, some black, the blue anodized ones were 40s probably they came on the 77-79RS.

You must be a member to view complete articles on this website. If you are already a member, you can log in here. If you aren’t a member yet, you can purchase a membership here.

Continue readingMore Tag

Experience with DOT 5 (Silicone) Brake Fluid

Do any of you have personal experience with DOT 5 brake fluid in Beemers? If so, I’d appreciate hearing from you, as to whether it was good or bad.  In the meantime, I’ll share mine with you.

My bike is a 1974 R90/6, purchased in December 1976 with 5k on the odometer.  It has a single-caliper front disc brake.  Removal of the fuel tank to top-up the brake fluid four months later revealed a jet-black liquid in the brake system, which I flushed out with clean DOT 3. Occasional checks thereafter revealed that the fluid in the reservoir remained clean and clear, and there were no leaks in the system.  By  1981 (31k), the fluid in the reservoir was starting to look like Sierra Nevada pale ale, so I flushed the system again with DOT 3.

In 1982, having had good luck with silicone (DOT 5) brake fluid in a 1971 MGB and a 1966 Buick for about three years, I decided to try it in my bike.  Advice to the contrary notwithstanding, I disassembled the master cylinder and front caliper, found the pistons and cavities clean and bright – no rust or corrosion – wiped out all the old fluid with a clean rag, washed loose parts with soap and water, reassembled using the original seals, and filled the system with DOT 5.  There had been a very slight seep between the master cylinder and the reservoir, but decided that it wasn’t bad enough to go to the trouble of removing the reservoir.

You must be a member to view complete articles on this website. If you are already a member, you can log in here. If you aren’t a member yet, you can purchase a membership here.

Continue readingMore Tag

Changing Brake Fluid

Fellow militant Airheads, As far as general maintenance goes how often do ya’ll change your brake fluid?

The correct answer to this can vary with the amount of humidity in your local air. The manual says do it once a year. You change the brake fluid because it absorbs water from the air. As it does so it gets darker, also its boiling point goes down. This water can eventually damage parts. As I write this I have this vision of someone with a low level of anal retention insisting on using the most exotic oil but not changing the fluid because it’s not yuppie. These are the folks whose Airheads retire early as being too expensive to fix.

You must be a member to view complete articles on this website. If you are already a member, you can log in here. If you aren’t a member yet, you can purchase a membership here.

Continue readingMore Tag

Broken front & rear brake light switches

This article is not concerned with the hydraulic pressure activated brake switches. Those switches, originally 34-31-1-233-959, were replaced with 61-31-1-244-334. You can probably substitute the switch used on old VW Beetles. Napa carries that switch as number SL143. There are other such switches: 3 terminal version is NAPA SL159, VW 113945515G; 2 terminal version is NAPA SL147, VW 0344004003.

This article IS concerned with the mechanically activated brake switches.   All R series bikes FROM 1985 model year through 1988, & SOME 1989 Airheads were affected. ALL models of Airheads for those years!

BMW Service Information Bulletins were issued regarding the front & rear brake light switches, brake lever, etc. The bulletins applied to both Classic K bikes & to Airheads, but not exactly the same way. There were bulletins issued in 1987, updated in 1988 & a formal recall in 1989. Later bulletins were longer, with more details.

You must be a member to view complete articles on this website. If you are already a member, you can log in here. If you aren’t a member yet, you can purchase a membership here.

Continue readingMore Tag

Posts navigation

1 2 3 4 5 6 … 10 11 12
Scroll to top